MC510-10 / MC610-10 / MC610-50

Technical Resources

Internal Access

The MC610 can be opened by the user. This does not void the warranty, however, any damage caused by doing so will not be covered.

The following steps will walk you through opening your MC610 case, as well as auto-powering on and clearing CMOS.

The case is very simple to open. To do so, remove the two screws from the back and slide the lid off towards the rear.

MC510-10 / MC610-10

Motherboard

Access the official Motherboard manual & OEM Resources from ASRock. This external link provides access to the complete motherboard manual, along with the latest BIOS updates and specific drivers for your system's motherboard (IMB-156).

BIOS

Warning: Never interrupt a BIOS update. If the update is interrupted, the system may become irreparable. Damage caused as a result of BIOS updates may not be covered by the system's warranty.

You can follow this for installation instructions.

1. Locate the PWR_JP1 jumper indicated by the orange circle

2. Move PWR_JP1 over by 1 pin

3. The unit is now configured for auto power on

1. Locate the clear CMOS jumper

2. Move the jumper over by 1 pin

3. Wait 30 seconds

4. Restore the jumper to its original position

Access the official from ASRock. This external link provides access to the complete motherboard manual, along with the latest BIOS updates and specific drivers for your system's motherboard (IMB-1212).

By default, only the Mini DP ports in the expansion bay are enabled. The motherboard’s onboard HDMI and VGA ports can be enabled in the BIOS to support additional displays.

Warning: Never interrupt a BIOS update. If the update is interrupted, the system may become irreparable. Damage caused as a result of BIOS updates may not be covered by the system's warranty.

You can follow this for installation instructions.

1. Locate the PWR_JP1 jumper indicated by the orange circle

2. Move PWR_JP1 over by 1 pin

3. The unit is now configured for auto power on

1. Locate the clear CMOS jumper

2. Move the jumper over by 1 pin

3. Wait 30 seconds

4. Restore the jumper to its original position

• Begin by removing the top 2 screws from the back of the unit.

• Slide the lid off towards the back

• Use a screwdriver to push out the two knockouts shown

• Grab the knockouts with pliers and twist to remove

• final result shown

• Connect the 4 pin plug to the motherboard. It only fits 1 way. Push down gently until it clicks in.

• Remove the nut and washer from the DC jack.

• Push the DC jack through the larger of the 2 holes.

• Install the washer and then the nut onto the DC jack from the outside of the case.

• Hand tighten.

• Slide the lid back on and reinstall the two screws

• Grab the retaining zip tie kit

• Push the zip tie into the hole

• Face the ribbed side upward

• Attach the clip to the power supply’s cable

• Thread the zip tie through the clip’s hole and snug into place.

• Use only the newly installed DC barrel jack to power the unit.

• NEVER connect both power connectors at once.

Access the official from ASRock. This external link provides access to the complete motherboard manual, along with the latest BIOS updates and specific drivers for your system's motherboard (IMB-1012J-WV).

Warning: Never interrupt a BIOS update. If the update is interrupted, the system may become irreparable. Damage caused as a result of BIOS updates may not be covered by the system's warranty.

You can follow this for installation instructions.

1. Locate the SIO_AT1 (#17) jumper indicated by the orange circle

2. Move SIO_AT1 over by 1 pin

3. The unit is now configured for auto power on

1. Locate the CLRMOS1 (#16) jumper

2. Move the jumper over by 1 pin

3. Wait 30 seconds

4. Restore the jumper to its original position

For the latest security advisories concerning OnLogic products, including vulnerability disclosures and necessary updates, please refer to our official Security Advisories page. It is recommended to regularly check this resource for critical security information.