Technical Resources

The MK150 can be opened by the user. This does not void the warranty, however, any damage caused by doing so will not be covered.

The following steps will walk you through opening your MK150 case, as well as auto-powering on and clearing CMOS.

Find your MK150 unit or model name on the right panel, and click on it to see the instruction set for it.

Internal Access

The MK150 case is very simple to open. Remove the two screws from the sides and slide the lid off towards the rear.

MK150B-10

Motherboard

Motherboard Manual

Drivers

Startup Settings

Auto Power On

1. Power on the unit and press the Del key to access the BIOS

2. Navigate to the Chipset tab

3. Change “Restore AC Power Loss” to [Power On]

4. Save changes and exit

5. Auto power on is now enabled

1. Locate the clear CMOS jumper

2. Move the jumper over by 1 pin

3. Wait 30 seconds

4. Restore the jumper to its original position

Technical information related to the system's motherboard can be found from the support link below.

1. Power on the unit and press the Del key to access the BIOS

2. Navigate to the Chipset tab

3. Open the “PCH-IO Configuration” menu

4. Open the “High Precision Event Timer Configuration” menu

1. Locate the JBAT jumper

2. Move the jumper over by 1 pin

3. Wait 30 seconds

4. Restore the jumper to its original position

Technical information related to the system's motherboard can be found from the support link below.

Technical information related to the system's motherboard can be found from the support link below.

1. Power on the unit and press the F2 key to access the BIOS

2. Navigate to the Advanced tab

3. Open the South Bridge Configuration menu

4. Change “Restore on AC/Power Loss” to [Power On]

1. Locate the CMOS battery

2. Carefully remove it from the holder

3. Wait 5 minutes

4. Reinsert the battery

Technical information related to the system's motherboard can be found from the support link below.

1. Locate the AT/ATX jumper

2. Move it over by 1 pin

3. Auto power on is now enabled

1. Locate the CLRMOS1 jumper

2. Move the jumper over by 1 pin

3. Wait 30 seconds

4. Restore the jumper to its original position

Technical information related to the system's motherboard can be found from the support link below.

1. Take the jumper circled in blue and move it to the pins circled in orange

2. The unit is now configured for auto power on

NOTE: The blue jumper is for LVDS display output. As the MK150B-53 does not use LVDS, we can borrow that jumper to enable the auto power on.

1. Locate the clear CMOS jumper

2. Move the jumper over by 1 pin

3. Wait 30 seconds

4. Restore the jumper to its original position

Technical information related to the system's motherboard can be found from the support link below.

1. Power on the unit and press the Del key to access the BIOS

2. Navigate to the Advanced tab

3. Open the Chipset Configuration menu

4. Change “Restore AC Power Loss” to [Power On]

1. Locate the clear CMOS pads

2. Short the two metal halves with a flathead screwdriver for 30 seconds

3. The CMOS is now clear

Technical information related to the system's motherboard can be found from the support link below.

1. Power on the unit and press the Del key to access the BIOS

2. Navigate to the Advanced tab

3. Open the Chipset Configuration menu

4. Change “Restore AC Power Loss” to [Power On]

1. Locate the clear CMOS pads

2. Short the two metal halves with a flathead screwdriver for 30 seconds

3. The CMOS is now clear

For the latest security advisories concerning OnLogic products, including vulnerability disclosures and necessary updates, please refer to our official Security Advisories page. It is recommended to regularly check this resource for critical security information.