This page also applies to the TM120 ThinManager Ready platform.
The ML100 can be opened by the user. This does not void the warranty, however, any damage caused by doing so will not be covered.
Ensure your body is discharged of any static electricity by touching a grounded metal surface.
Remove the 4x phillips screws on the outside of the case.
Use the tab for leverage to pull the bottom panel off
The internals of the unit can now be accessed
Technical information related to the system's motherboard can be found from the support link below.
● Power on the unit and press F2 a few times to access the BIOS. ● Navigate to the Advanced tab ● Open the Chipset Configuration menu ● Locate the Restore on AC/Power Loss option ● Set it to Power On ● Press escape twice to go back ● Navigate to the Exit tab, Save Changes and Exit
Disconnect the system from all wire connections (power, ethernet, video, etc), then:
● Locate the clear CMOS jumper ● Move the jumper over by 1 pin ● Wait 30 seconds ● Restore the jumper to its original position ● Close up and power on the system. It may power cycle several times before it begins working again.
For increased reliability it is recommended to disable the Core Performance Boost BIOS setting. To disable the setting, navigate to: Advanced -> CPU Configuration -> Core Performance Boost -> Set to “Disabled”
Press F10 to Save & Exit.
Technical information related to the system's motherboard can be found from the support link below.
***Please note that the AMD CPU’s Core Performance Boost (similar to Intel’s TurboBoost) is disabled on this series in order to maintain thermal performance in line with the expected operating temperature.***
The auto power on feature will automatically turn the ML100 back on after DC power is lost and restored. To enable it, a jumper needs to be moved inside the unit. The ML100 can be opened by the user. This does not void the warranty, however, any damage caused by doing so will not be covered.
Ensure your body is discharged of any static electricity by touching a grounded metal surface.
Remove the 4x phillips screws on the outside of the case.
Use the tab for leverage to pull the bottom panel off
Remove the two screws from the USB board and gently lift it out of the way, leaving it plugged in.
Remove the blue jumper circled at the top and place it on the 2 pins circled in the bottom left.
Note: We are borrowing the clear CMOS jumper for this procedure. If CMOS needs to be cleared at a later date, keep that in mind.
Auto power on is now enabled and good to go.
For increased reliability on systems with the optional 4X4-V2000M CPU, it is recommended to disable the Core Performance Boost BIOS setting. To disable the setting, navigate to: Advanced -> CPU Configuration -> Core Performance Boost -> Set to “Disabled”
Press F10 to Save & Exit.
Disconnect the unit from all wire connections (power, USB, ethernet, etc.)
Remove the 4x phillips screws on the outside of the case.
Use the tab for leverage to pull the bottom panel off
Remove the two screws from the USB board and gently lift it out of the way, leaving it plugged in.
Locate the clear CMOS jumper
The jumper will initially be in this position.
Move the jumper over by 1 pin
Wait 30 seconds
Move the jumper back to its original position.
Re-assemble and power up the PC. Do not touch it for 2 minutes to allow it time to reconfigure itself. If it still does not respond, contact OnLogic support.
Technical information related to the system's motherboard can be found from the support link below.
Update the BIOS with the file(s) above. You can follow this guide for installation instructions.
Locate the jumper from your system’s accessory box.
If you need a replacement, this is a standard 2.54mm jumper. Available from .
Ensure your body is discharged of any static electricity by touching a grounded metal surface.
Disconnect the unit from all wire connections (power, USB, ethernet, etc.)
Remove the 4x phillips screws on the outside of the case.
Use the tab for leverage to pull the bottom panel off
Locate the auto power on header
Place the jumper onto the header. Use needle nose pliers if available.
Auto power on is now enabled.
Re-assemble the system and it will turn on automatically when you plug it in.
Disconnect the unit from all wire connections (power, USB, ethernet, etc.)
Remove the 4x Philips screws on the outside of the case.
Use the tab for leverage to pull the bottom panel off
● Locate the clear CMOS jumper\
Using a flathead screwdriver or similar conductive metal object, short the outer 2 pins of the CMOS header for 30 seconds.
Re-assemble and power up the system. Wait patiently for 2 minutes as it will need to restart a couple times to reconfigure.
If the unit is still unresponsive after 2 minutes, contact support@onlogic.com.
For the latest security advisories concerning OnLogic products, including vulnerability disclosures and necessary updates, please refer to our official Security Advisories page. It is recommended to regularly check this resource for critical security information.
1.80A
Update to include Intel I226 LAN support
