BIOS Version 1.04

1- Getting Started

1.1 - Introduction

The UEFI BIOS is a small program which runs when your computer starts and configures its basic functions. That configuration is automatic, and most users will be satisfied with the default configuration. If the default configuration is not sufficient, the BIOS has setup menus which can be used to reconfigure the computer.

The purpose of this manual is to document the function of the BIOS and its available configuration options. The text of this document lists the BIOS menus and options exactly as they appear in the BIOS menus: in the correct order, with the correct default values for this BIOS version. Some options are hidden based on how other options are set and which hardware is detected in the system, so some options may not appear on all systems. Informative screenshots are also provided throughout, but their contents may not exactly match this BIOS version.

1.2 - Navigating the Setup Menu

To access the BIOS setup menu, hold the DEL key on the keyboard while turning on the system. After a few seconds, the BIOS front page menu is shown:

On each menu, the selected option is shown in white, other options are shown in blue, and read-only options are shown in gray. Some menus have multiple screens, which are shown at the top of the screen. The active screen is shown with a gray background and inactive screens are shown with blue backgrounds.

BIOS menus are navigated by pressing keys on the keyboard:

• F1 shows help on available keyboard shortcuts

• ↑/↓ arrow keys select the option above or below the currently-selected option

• →/← arrow keys activate the screen to the right or left of the currently-activated screen

To access the BIOS boot manager, hold the F10 key on the keyboard while turning on the system. After a few seconds, the BIOS boot manager is shown:

To access the Secure Boot Menu, hold the Ctrl+Alt+F4 key on the keyboard while turning on the system. After a few seconds, the Secure Boot menu is shown:

• The system will prompt you to set admin passwords to configure secure boot for the first time.

• Enter the admin password to access the secure boot setting page.

The Error LED is effectively controlled by BIOS based on the following conditions:

Blinking frequencies:

• Slow blinking: 0.5 Hz (Blinks once every two seconds)

• Medium blinking: 1 Hz (Blinks once every second)

• Fast blinking: 4 Hz (Blinks four times every second)

When RTC battery is low, BIOS will display "Warning: Low RTC battery" for 30 seconds during the BIOS POST.

If a BIOS update is interrupted, your system may fail to boot. The system will attempt to recover in two ways:

1. Automatic Recovery

The system will automatically try to restore the original BIOS image.

• Look for the text "Crisis Recovery" on your screen.

• This indicates the repair is in progress.

2. Manual Recovery (USB Method)

If the system keeps rebooting and does not recover automatically, follow these steps:

1. Save a valid BIOS image file onto a USB flash drive.

2. Rename the file to: CL260.bin

3. Insert the USB drive into the computer.

You can enable the Factory Reset Button under Onlogic Feature Configuration of the BIOS setup menu

1. Turn off the system completely.

2. Press and hold the Factory Reset button.

3. While still holding Reset, press the Power button to turn the system on.

4. Wait 5 seconds after the system powers up, then release the Factory Reset button.

The Result:

• All BIOS settings return to default.

• Admin passwords are deleted.

SSD S.M.A.R.T Health Check is enabled by default in the Onlogic Feature Configuration

BIOS will check the SSD health status and display warnings if the status is bad for 30 seconds

• Normal Operation: Once the computer boots to an OS, the BIOS constantly resets a hidden countdown timer to prove the system is still running smoothly.

• If the system freezes ("hangs") and stops working, it fails to reset that timer.

• When the timer runs out (hits zero), it automatically forces the computer to restart to recover from the freeze.

To enable In-Band ECC in the memory configuration page, Intel Trusted Execution Technology must be disabled in the CPU configuration page.

Several options are available on the Main page:

• Platform information: a comprehensive summary of the computer's hardware components and firmware details

• Language: Select which language to display

• System Time: adjust RTC time

The Advanced menu contains the following options:

• BT

  • Enable/Disable BT module

• WIFI

Enabling Turbo Mode on the CL260 Description By default, Turbo Mode is disabled in the shipping BIOS to prevent total power consumption from exceeding the maximum output of the power adapter, particularly when Power over Ethernet (PoE) is utilized to power external devices.

If you are not using PoE as a power source, you may follow the instructions in this guide to enable Turbo Mode via the BIOS Setup Utility.

1. Power on the system and press [DEL] to enter the BIOS Setup Utility. Navigate to the [Advanced] tab and select [RC Advanced Menu].

1. Within the [RC Advanced Menu], select [Power & Performance].

1. In the [Power & Performance] menu, select [CPU Power Management Control].

4. Locate [Turbo mode] at the top of the menu. Select this item and press [ENTER] to change the value from [Disabled] to [Enabled]. No other settings need to be modified.

5. Press [F10] to save your changes and exit the BIOS Setup Utility. Turbo Mode is now enabled on your CL260.

The Security menu contains the following options:

• Current TPM Device (read-only; possible values: Not Detected, TPM 1.2, TPM 2.0)

• TPM Active PCR Hash Algorithm (read-only)

• TPM Hardware Supported Hash Algorithm (read-only)

The Power menu contains the following options:

• Wake on RTC from S5

  • Auto wake on S5, By Day of Month or Fixed time of every day

• Restore AC Power Loss

The Boot menu contains the following options:

• Network Stack

  • Network Stack Support: Windows 8 BitLocker Unlock, UEFI IPv4/IPv6 PXE, Legacy PXE OPROM

• PXE Boot capability

The exit screen provides options to leave the setup utility and to load and save settings.

• Exit Saving Changes: saves the current configuration and restarts the system to apply it

• Save Change Without Exit: saves the current configuration but does not restart the system

• Exit Discarding Changes: returns to the front page without saving or applying the current configuration

1- Product Overview

Ultra-small form factor computers that are designed to be reliable and feature-rich, with a fanless and ventless design for durability and effective cooling. The CL200 series are IoT-ready with configurable options for 4G LTE, Wi-Fi/Bluetooth, and advanced functionalities like Movidius and multi-CEC. Measuring just 34 mm x 115 mm x 82 mm, the CL200 can be installed in compact spaces while maintaining connectivity.

1.1- Box Contents & Accessories

Accessories

• Power Adapter

• Thermal Pads

Thermal Pads are used to assist with cooling expansion mSATA and mPCIe cards. If you purchased your system with expansion cards pre-installed, the thermal pads will already be installed inside the system. If you purchased additional items such as mounting brackets, power supplies, or antennas, they will be located in the system box or within the outer shipping carton.

CL210 & CL250 Exterior

Memory and storage are soldered on the motherboard for the CL200 Series computers. Memory for both systems are LPDDR4 dual channel RAM. Both systems use industrial-grade eMMC onboard storage. Manufacturers and part numbers are subject to change, so please check the system pages for updates. Additional storage is available using the uSD card Revision 3.01 (SDXC) supporting up to 2TB.

The audio jack is implemented using the Realtek ALC233-VB2 and supports Nokia and Apple headset connectors.

The serial port header is 2x5, 2.54 mm pitch, colored black and keyed at pin 10.

Standard pin-out supports half-height PCIe/USB and full-height PCIe/USB/mSATA signal.

Jumper Set Up

The following illustration shows how to use jumpers.

“Short” pins together by placing the jumper shunt on pins. Pins not capped with jumpers are “open”. With the illustrated 3-pin jumper, the shunt shorts pins 1 and 2. Check the corresponding header pin attributes to see what functionality is supported by shorting different pin pairs.

The following illustration shows the header without any jumpers.

This illustration shows jumpers in the default 6-4 and 5-3 positions.

Clearing the CMOS

Setting the jumper with the Clear CMOS jumper shunt allows you to clear the data in the CMOS. NOTE: Do not clear the CMOS right after updating the BIOS. You must boot up the system first and then shut it down before clearing the CMOS. NOTE: The password, date, time user default profile will be cleared only if the CMOS battery is removed.

To clear and reset system parameters to the default setup, follow these steps:

1. Turn off the computer and unplug the power cord from the power supply.

2. Wait 15 seconds.

3. Remove the jumper shunt from pins 6 and 4 and use it to short pins 2 and 4 on the header for 5 seconds.

The 3V Battery coin cell cable header is clearly labeled:

If it was selected and configured in the build, the chip will be populated. CEC functionality will work with an HDMI adapter. Please see series pages for additional information.

Onboard Intel HD Graphics 500 processing circuitry is integrated into the processor. Single Display supports a maximum resolution of up to 3840x2160 (4K) @ 60 Hz. Dual independent displays are achieved through the optional second Mini-Display Port. Up to three mirrored displays are achieved via Display Port v1.2 daisy chaining.

The CL200 Series supports multiple power states. These states can be configured on the motherboard. This section describes the power management functions you can perform.

An unexpected shutdown does not necessarily cause a loss of data, but it can make access to some of your data difficult. To remedy this possibility, follow this procedure to power up the system again after the system power has been off for more than 4 seconds:

• If the SOC BIOS mode is set to AT mode, press the Power button once to power on the system.

• If the SOC BIOS mode is set to ATX mode, press the Power button twice to power on the system.

The motherboard supports the following wake-up events.

Notes: S4 implies OS support only. USB ports must be turned off during S4/S5 states.

1. Step 1: Mark and prep holes in surface for mounting.

2. Step 2: Attach wall mount brackets to chassis.

3. Step 3: Fasten system to surface.

1. Step 1: Attach DIN Rail mounting brackets to the chassis.

2. Step 2: Clip system to the DIN Rail.

It is important to read the following precautions before installing expansion cards into the motherboard:

• Wear a grounding strap attached to a grounded device to avoid damage from static electricity.

• Before opening the system, discharge static electricity by touching the metal case to a grounded object.

• Leave components in the static-proof bags they came in until they can be installed.

• Remove the two silver Phillips screws

• Use a flathead screwdriver or similar tool to gently lever the bottom cover off

• Hinge the bottom plate back onto the system by aligning the tabs

• Reinstall the silver Phillips screws

To add Wi-Fi to the CL200 Series, follow this procedure.

1. Before starting, ensure that you have read and understand the installation precautions listed above in the "Pre-Installation Precautions" section. \
2. Remove both screws from the front of the case. Retain screws. \
3. Remove the cover of the unit by sliding it toward the rear. \

The following section describes the CL200 Series UEFI. It shows each screen menu with a table describing the various fields and values.

SMART Settings

NCT5524D Super IO Configuration

Hardware Monitor

S5 RTC Wake Settings

CPU Configuration

Socket 0 CPU Information

CPU Power Management

AMI Graphic Output Protocol Policy

Network Stack Configuration

USB Configuration

Platform Trust Technology

Thermal

System Component

RC ACPI Settings

PCI Express Configuration

PCI Express Root Port 3

LAN 1

PCI Express Root Port 5

LAN2

USB Configuration

Secure Boot

UEFI Hard Disk Drive BBS Priorities

Update the BIOS with the file(s) above. you can follow this for installation instructions.

Windows 10

Download and extract it. In the Windows 10 folder, there are two applications required for full functionality, the kernel driver that allows communication with the CEC module, and the user driver that keeps the module up-to-date with the system’s HDMI port addresses. To install the kernel driver, right-click on ADP107.inf and select install. Accept any prompts that follow, then restart the system.

Linux

Download and extract it. Install the necessary prerequisites using:\

In the Linux folder, you will find a kernel module that can be compiled from the command line. From the driver package’s Linux folder, run the following commands:\

Finally, restart the system. Upon reboot, you should find that a character device is loaded at /dev/adp107 that can be used to communicate with the device using the application codes included in the next section.

Ubuntu – Scan for HDMI addresses and power up displays Prerequisites: python-smbus

• Power on the CL200 and press the Esc key a few times to access the BIOS

• Navigate to the Chipset tab

• Change auto power on to [enable]

• Enter the BIOS and ensure that the watchdog timer is enabled. The option is at the top of the Advanced settings page.

• Install the watchdog package using `sudo apt-get install watchdog`.

• In the terminal, run `lsmod | grep wdat_wdt` to see if the watchdog module is loaded. If the command returns nothing, the module is not loaded.

• Locate the Clear CMOS jumpers

• Remove the black jumper from pins 6 and 4

• Install it onto pins 4 and 2, moving it down by 1 pin

• Open the system following the Disassembly steps above.

• Install the WiFi and/or mSATA card as shown. Install the WiFi antenna pigtail cables as shown.

• The nuts and washers are loose for illustration purposes. They should be fully hand tightened

• Apply the thermal pad to the top of the WiFi/mSATA card. This can be located in your system’s accessories.

The ADP107 is a module that is installed in-line with the DisplayPort outputs on configured OnLogic systems. Its purpose is to enable Consumer Electronics Control (CEC) functionality which manages the connection between the system and any connected displays according to a set of preconfigured rules. This allows command signals to be passed to the displays when the computer starts, stops, wakes, and sleeps, in a user-configurable order after a configurable time delay.

The device’s default configuration is to power up displays when the system starts/wakes and power them off when the system stops/sleeps. It is also configured by default to start the computer when the connected display powers on, and to power the computer off when the displays are powered off. The default startup delay timer is set to 5 seconds.

This document provides international regulatory and safety compliance information for the OnLogic Fanless computers xxxx-CL2YY-xxxx, (where x can be any alphanumeric character or blank and Y is numeric character) computer system.

For more information on accessories and additional features, visit the product page:

FCC

This device complies with part 15 of the FCC rules as a Class A device. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that might cause undesired operation.

Industry Canada Compliance Statement

This Class A digital apparatus complies with Canadian ICES-003.

Avis de Conformité à la Réglementation d’Industrie Canada

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

CE

This equipment complies with all applicable European Union (CE) directives if it has a CE marking. For this device to remain CE compliant, only CE compliant parts can be installed, and proper cables and cabling techniques are required.

1. Do not open or modify the device. The device uses components that comply with FCC and CE regulations. Modification of the device will void these certifications.

2. Install the device securely. Be careful handling the device to prevent injury and do not drop.

3. Wall or ceiling mounting device requires use of a mounting plate or bracket. Plate or bracket must be of metal construction and have a minimum thickness of 1mm.

WARNING: There is danger of explosion if the CMOS battery is replaced incorrectly. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion.

If this product was configured with a wireless device, the FCC and IC IDs will be detailed on a label on the chassis.

For the latest security advisories concerning OnLogic products, including vulnerability disclosures and necessary updates, please refer to our official Security Advisories page. It is recommended to regularly check this resource for critical security information.

1- Product Overview

1.1- Introduction

An ultra-compact, fanless edge gateway with dual LAN, dual Display over USB-C, and Intel® Quad-Core processing.

For more information on accessories and additional features, visit the CL260 product page:

• https://www.onlogic.com/store/cl260/

1.2- Safety

1.3- Box Contents & Accessories

If you purchased additional items such as mounting brackets, power supplies or terminal block connectors, they will be located in the system box or within the outer shipping carton.

For more information on accessories and additional features, visit the CL Series Product page.

CL260 Product Page:

The CL260 is pictured with 2 RP-SMA antenna plugs.

The front power button can be used to turn on and off the CL260 system. The power button is a momentary contact button without LED.

• A single press while the system is on will initiate a graceful Shutdown or Sleep operation from the OS

• Pressing and holding the button for 4 seconds while the system is running will cause a forced shutdown

• The system can be woken by a single press of the power button from any state

• USB 3.2 Gen 1 (5 Gbps)

• DisplayPort 1.4 compliant in DisplayPort Alt Mode

• Power output up to 5V/3A

• USB 3.2 Gen 1 (5 Gbps)

The LAN Ports on CL260 supports up to 1Gbps link speeds over standard shielded CAT5e or CAT6 cables. The connector is the industry standard RJ45 connector. The LAN link state is shown by the two LEDs enclosed in the port. The description is included below.

When Factory Reset Button is pressed, it resets system BIOS settings back to factory defaults. In order for the factory reset button to be functional it must be enabled in the BIOS setup menu.

The mainboard power is applied to the CL260 platform through a 3-pin terminal block connector (Mating part: Dinkle / OnLogic 0225-0603 or equivalent).

The system is operational from 12V~24V. The maximum rated current of the connector is 15A per pin. Use a wire gauge that is rated for the operational current. Cables should be properly terminated with wire ferrules. Do not use the terminal block with tinned wire ends or solid core wire. See below for the connector pinout which is also indicated on the terminal block mounting panel adjacent to the connector. Installation of DC Mains connection shall only be performed by skilled personnel and in accordance with your local and national electrical code (Example: NEC, CEC).

When using the remote switch connections with the terminal block option, mating power switch cables should be a twisted-pair wire with floating shield to assure proper immunity to EMI/RFI. It is recommended to keep wires at less than 3 meters in length. Switches should be momentary contact type only.

• USB 3.2 Gen 1 (5 Gbps)

• DisplayPort 1.4 compliant in DisplayPort Alt Mode

• Power output up to 5V/3A

Serial Port (10-Pin Terminal Block)

The serial ports support RS-232, RS-422, and RS-485 configurations. Refer to the for configuration instructions.

(Mating part: Dinkle 0159-0110 / OnLogic TB10P or equivalent).

The motherboard top and bottom view for CL260 is as below.

An M.2 E-Key port is present on the Helix motherboard to allow support for E-Key form-factor wireless expansion cards. Only 2230 form-factor cards are supported. The E-Key connector on the CL260 platform supports PCIe Gen 3 x1 and USB 2.0.

A full pinout table for this expansion slot is provided in Expansion Port Pinout

An M.2 M-Key port is present on the Helix motherboard to allow support for M-Key form-factor expansion cards. Only 2280 form-factor cards are supported. The M-Key connector on the CL260 platform includes support PCIe Gen 3 x2 and SATA III.

A full pinout table for this expansion slot is provided in Expansion Port Pinout

If the BIOS needs to be updated, please refer to the for reflashing instructions.

The RTC battery on the CL260 platform is used to maintain the real-time clock for the system. If the RTC battery is low, the Error LED will indicate the error event. The cabled RTC battery should be replaced with an UL listed battery. The battery shall use a ACES 50276-002H or equivelent connector to mate with the on-board connector.

Two Intel Twin Lake Processor options are available for the CL260.

The CL260 platform has the onboard LPDDR5 chips:

• Capacity: 8GB

• Speed: 4800 MT/s

The power consumption of the CL260 system was measured for various system configurations, workloads, and power states at 12V system input voltages. Tests were performed using BurnInTest v10.2 to stress system components. The build configurations and power consumption are listed in the tables below.

*The configurations below are using representative samples of internal devices, the specific components mentioned below may vary from the devices provided by OnLogic. The power consumption for each system configuration is record below

Configuration 1 : N150

Configuration 2 : N250

These DC levels specified are the absolute max values for the pins for function and safety of the system. The protection circuitry allows for brief transient voltages above these levels without the system turning off or being damaged. A transient voltage suppressor on the power input allows momentary excursions above stated limits. For input power consumption and current see Power Consumption

The CL platform supports multiple power states. The wake-up events can be configured in the BIOS. This section describes the supported power management functions and gives information on protection circuitry for power adapters. Low power shutdown is an additional option in the BIOS. See for more information.

Pressing Delete key while the system is booting, then navigate to Power -> Restore AC Power Loss Select Power On to enable auto power on Select Power Off to disable auto power on

• Temperature Range: 0ºC to 50°C

• Step size: 10°C

• Place the system in a chamber with 0.7 m/s of airflow and run the Furmark stress test

Step 1: Align the two screw holes on the back of the system with the respective holes on the DIN Clip (MTD109).

Step 2: Attach DIN Clip (MTD109) to the system using the supplied M3 screws (M3X0.5 Flathead Screw, 6mm Long).

Step 3: Mount system onto the DIN rail.

Note: The mounting brackets are required to support 4x the hanging weight of the system. The mating surface and hardware must be capable of supporting the same load.

Step 1: Align the two screw holes on the back of the system with the respective holes on the VESA mounting bracket (MTW117).

Step 2: Attach VESA Mounting Bracket (MTW117) to the system using the supplied M3 screws (M3X0.5 Flathead Screw, 6mm Long)

Step 1: Peel feet from releasing paper.

Step 2: Adhere feet on the bottom side or CL260.

Properly opening OnLogic systems does not void the warranty in most cases, however, some precautions are necessary to avoid damaging the system.

• Perform this disassembly in an area free of static discharge.

• Disconnect power, video, and any other connections to the system. It should be fully unplugged.

• Ideally, wear a grounding strap. If that is not available, regularly touch a grounded metal surface to discharge your body of static electricity.

Windows 11 Drivers -

(Follow our guide for )

For the full BIOS manual, please .

*Update the BIOS with the file(s) above. You can follow this guide for installation instructions. PLEASE NOTE - this is a SIGNED BIOS.

The BIOS controls the serial port configurations. Go to the following BIOS settings to adjust the communication types. Access the BIOS by pressing <DEL> at boot up.

Set the communication type, navigate to:

Advanced –> Serial Port

• RS232 (default)

• RS422

• RS485

Make sure to save any changes by pressing F10 to Save and Exit.

The CL260 features a factory reset button to manually restore the BIOS to its default settings.

1. Locate the factory reset button on the front plate.

2. Press the reset button to restore system BIOS settings back to factory defaults or custom set values.

120-ohm termination resistor:

For RS-422 and RS-485, the internal 120Ω termination resistor is enabled by default.

RS-485 Built-in biasing/fail-safe:

The transceiver supports enhanced fail-safe operation and does not require external biasing resistors to maintain a defined receiver state when the bus is idle.

Standard RS-485 biasing:

The transceiver implements an enhanced fail-safe receiver function. When the bus is open, shorted, or idle (un-driven), the receiver output is guaranteed to remain at a logic-high state. Therefore, no external RS-485 biasing resistors are required.

This device has been tested to the relevant EMC and Safety standards. Modifications by the user may invalidate certifications. Testing included EN 55032, EN 55035, EN 60601-1-2, EN 62368-1, EN 18031-1 (RED 3.3d) and IEC 60945 Ed. 4.

This device complies with part 15 of the FCC rules as a Class A device. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

The computer system was evaluated for medical, IT equipment, automotive, maritime and railway EMC standards as a class A device. The computer complies with the relevant IT equipment directives for the UKCA mark.

For the latest security advisories concerning OnLogic products, including vulnerability disclosures and necessary updates, please refer to our official Security Advisories page. It is recommended to regularly check this resource for critical security information.